19 Most Common Laser Engraver Problems And Solutions

A: check whether the circulating water is unobstructed. You can also try decreasing the flow of coolant or using a heating gel. As a business engaged in laser engraving, you know how important it is to troubleshoot any issues that may arise. When measuring the voltage at pins 7 and 20, it's important to avoid pre-adjustment and to follow the normal signal (low-level conductivity). In this case, the problem is most likely with the signal. Whether 5V/12V/24V switching power supply is normal, also remember to check the display panel, etc. With the vector cut the laser just traces the lines of the cut. Check to see if the connection cable is loose or the control panel button contact is bad. The Seventh Problem: Computer Can Not Output for Laser Engraver. 10 Tips and Tricks for Laser Engraving and Cutting : 10 Steps (with Pictures. That knowledge will help to sharpen your skills with the laser engraver and cutter. To troubleshoot, here are some things you might need to do.

• Laser engraving and etching
• Laser marking and engraving
• Laser engraving problems and solutions
• Laser engraving problems and solutions how to
• Laser engraving problems and solutions manual
• Laser engraving machine repair

Laser Engraving And Etching

High-voltage lines are down. While it is possible to have other errors on your controller, these are by far the most common. The depth of field refers to the length of the laser power-dense area which can form the processing ability after laser focusing (figure). But there is a way to tick the laser and get thicker lines. The laser I work with is an Epilog Helix and the program we use to run it is Corel Draw. The laser power source is malfunctioning. Laser engraving machine repair. B: if the indicator light is on, check whether the motor wire connection is good. The motherboard serial port is damaged and needs to be repaired or replaced. This can lead to two problems: - Larger codes require more marking time or more laser power.

Laser Marking And Engraving

Laser Engraving Problems And Solutions

Then run the file and watch where the red dot goes. The bursting is normal, indicating that the power supply is not faulty, and the bursting is not normal, indicating that there is a problem with the power supply; 5. How to solve the malposition problems of laser engraving and cutting machine –. The corners look like they have little dots in them. High voltage line sparks. Codes with more information need more modules, which leads to larger codes or smaller cells. Computer operation is correct.

Laser Engraving Problems And Solutions How To

Sometimes the light deviation is caused by the deformation of the guide rail. Computer and the laser engraver should use the same electrical outlet to avoid any potential difference. The laser tube may be aging and needs to be replaced. Laser Engraver Errors: Common Ruida Controller... - Training Blog –. In these cases, annealing is the recommended laser process, especially in the medical and food & beverages industries. The surrounding yellow light is not strong when cutting, and the blowing is weak. So you've designed a logo or a image and you want to burn it onto a piece of wood. If using LightBurn, check to ensure no layers outside of the design area are set to output (they may not be visible but can still have output turned on). The common symptoms of faults in equipment are: (1) The laser head does not move.

Laser Engraving Problems And Solutions Manual

If this does not fix the issue, it is possible that the door sensor needs to be adjusted or replaced. Check the mirror system is normal, without loosing. If so, modify the file to a suitable size. Whether the serial port line has been used to connect the computer serial port and engraving machine, the connection is reliable. Low setting power for the laser tube. Marking machine and cutting machine have incorrect marking or cutting dimensions. Laser marking and engraving. If you don't want that cover the surface with masking tape to protect it. The DPIO module driver has not been installed. Unlike the other options, it does not remove material from the metal surface.

Laser Engraving Machine Repair

The X and Y axis cannot move. This kind of problem is usually caused by light deviation or uneven work surface, which requires dimming or adjusting the platform surface. No display on the boot display panel. The computer's plug-in is damaged.

1 post • Page 1 of 1. The speed and power of the laser beam can be adjusted to create different effects. For example, a barcode could be 18 modules wide and 18 modules high (18x18). Improper light polarization. The water circulation system is not functioning (due to blocked pipes or non-working pumps). If both the motor and the driver are excluded, it is necessary to consider the motor wire and detect any short-circuits or open-circuits by using a multimeter to make detailed continuity measurements. Computer system is wrong. 5" down from the top and 1. Then I run the laser on a vector setting (with a lower power setting and a higher speed). Increase the working current, but do not exceed the maximum working current of the laser tube, otherwise, the laser power will decrease, such as 80w 20mA, 130w: 22mA. The water temperature is higher than 30 ℃. Reducing the focus size: for most applications, reducing the spot size is more effective than increasing the working current of the laser tube or replacing a larger laser tube, and the cost is lower. The lenses are seriously polluted. Lower the following sensitivity in the software settings; b.